Thank you for taking the time to express your issue. This is most common when a system driver is forced to be updated. The steps below will assist you in resolving this:
- Turn on the computer and keep pressing F9. It should take you to the Windows Recovery console.
If the problem persists, follow the procedures recommended by Greg Carmack, a Windows MVP, in this article.
thread. You can also contact your supervisor directly.
To assist you with some BIOS troubleshooting methods, contact the computer manufacturer.
On an Acer laptop, how can I leave the Aptio setup utility?
If your computer is stuck in Aptio Setup Utility, you can turn it off completely by pressing and holding the power button. Then, while holding down the power button, press F9 repeatedly for around 10 seconds.
After that, select Advanced Startup and wait for the recovery menu to emerge. After that, go to Advanced settings > System Restore and pick a date.
If your computer does not have a floppy drive but it is enabled in BIOS, you can access the Aptio Setup Utility main menu. To continue, press F1 while the computer is loading up. The fix is to restart the machine, go into BIOS, and disable the floppy drive.
If the motherboard loses power, data is lost, resulting in the Asus Aptio Setup Utility loop. Replace the battery to resolve the problem.
Final Method: Reinstall Windows 11/10/8/7
Finally, if none of these methods work, you might choose to reinstall the Windows operating system. However, you should be aware that your hard disk is in good working order.
What is the procedure for exiting the Aptio setup utility?
What is the procedure for exiting the Aptio setup utility?
- In the Aptio setup utility, go to the Boot menu, pick ‘Launch CSM,’ and toggle it on.
- In the Aptio setup utility, go to the Security menu, select’secure Boot Control,’ and set it to disabled.
What’s the deal with my laptop’s Aptio setup utility?
Simply restart the machine to see if that helps. It’s all you need at times. B. Restart the machine after restoring the BIOS (also known as Aptio Setup Utility) to its default settings.
What is the procedure for exiting Aptio setup utility 2021?
Some of you may have run into the problem when the machine boots straight into Aptio Setup Utility rather than the operating system.
So, how can you fix this mistake by making the computer boot into the operating system instead of the Aptio Setup Utility? Try the fixes listed below.
In the aptio setup utility, how can I disable secure boot?
Step 1: Turn on your Asus laptop and wait for the Aptio Setup Utility window to appear. Step 2: Expand the Secure Boot Control menu in Security and make sure the Secure Boot option is off. Step 3: Save and close the tab, then restart your computer and wait for Aptio Utility to load the settings again.
What’s the best way to get out of the boot menu?
Switch on the computer (or CTRL-ALT-DEL if you are already stuck on the boot menu) F2 should be held down (or whatever your BIOS menu key is) Disable Secure Boot from the Security Menu. Exit and save.
In Windows 10, how do I exit the setup utility?
Follow the steps below to remedy the problem you’re having:
- In the Aptio setup utility, go to the Boot menu, select Launch CSM, and toggle it on.
- In the Aptio setup utility, go to the Security menu, select Secure Boot Control, and set it to disabled.
Restart your computer and press the key that takes you to the BIOS setup screen. Depending on your computer, the precise key is different. The F2 key, for example, will open the BIOS on some Dells, whereas F10 will open the BIOS on some HPs and F1 will open the BIOS on some Lenovos. If you have a different brand of computer, look at the screen carefully when you first switch it on; it should prompt you.
To reset the machine to its default, fall-back, or factory settings, use the arrow keys to browse through the BIOS menu. Select the “File” option on an HP PC, then “Apply Defaults and Exit.” Press “F9” or select “Exit” followed by “Load Optimal Defaults” on a Lenovo. Press “Alt-F” on a Dell. Consult your computer’s owner’s handbook for specific instructions.
What is the best way to restart my laptop?
In the taskbar’s lower left corner, click the Windows Start button. 2. Select Sleep, Shut Down, or Restart from the flyout that appears when you click the power button icon. Hard Restart
- For around 5 seconds, press and hold the power button on the front of the computer.