Why is MAPP gas no longer produced?
Because of its high flame temperature of 2925 C (5300 F) in oxygen, genuine MAPP gas can be used in conjunction with oxygen for heating, soldering, brazing, and even welding. Although acetylene has a higher flame temperature (3160 C, 5720 F), MAPP has the advantage of requiring no dilution or special container fillers during transportation, allowing a larger amount of fuel gas to be transported at the same weight, and it is considerably safer in use.
Due to the high concentration of hydrogen in the flame higher than acetylene but lower than any of the other petroleum fuel gases a MAPP/oxygen flame is not totally suitable for welding steel. The hydrogen corrodes the welds by infusing itself into the molten steel. This is not a severe concern for small-scale MAPP welding because the hydrogen escapes rapidly, and MAPP/oxygen can be utilized to weld small steel pieces in practice.
Underwater cutting, which necessitates high gas pressures, MAPP/oxygen was shown to be beneficial (under such pressures acetylene can decompose explosively, making it dangerous to use). Underwater oxy/fuel gas cutting of any kind, on the other hand, has mostly been supplanted by exothermic cutting, which is faster and safer.
MAPP gas is also utilized in air combustion for brazing and soldering, where its higher combustion temperature of 2,020 C (3,670 F) in air gives it a modest edge over rival propane fuel.
The most significant disadvantage of MAPP gas is its high cost, which is typically one-and-a-half times that of propane at the refinery and up to four times that of propane at the consumer level. It is no longer widely utilized in any large-scale business; for bigger users, acetylene/oxygen is more cost-effective than MAPP/oxygen when high flame temperatures are required, and propane/air is more cost-effective when significant amounts of overall heating are required.
A MAPP/oxygen flame, on the other hand, is still extremely desired for small-scale users, as it has higher flame temperatures and energy densities than any other flame other than acetylene/oxygen, but without the hazards and hassles of acetylene/oxygen. It comes in handy for jewelers, glass bead makers, and a variety of other craftspeople. The high heat capacity of the MAPP/air flame is particularly valued by plumbers, refrigeration and HVAC experts, and other craftsmen; MAPP was frequently utilized until recently, and was provided in small to medium size containers.
Blowtorches are used to brown and sear food cooked sous-vide at low temperatures. MAPP gases should be used instead of cheaper butane or propane, according to Myhrvold’s Modernist cuisine: the art and science of cooking, since they create greater temperatures with less chance of giving the dish a gas flavor, which can occur with incompletely combusted gas.
Is MAP gas hotter to burn than propane?
MAP-Pro gas burns at 3,730 degrees Fahrenheit, while propane burns at 3,600 degrees Fahrenheit. MAP-Pro gas is a superior alternative to propane for soldering since it heats copper faster and at a higher temperature. If you do decide to use it, the manufacturer recommends that you use a torch that is specifically built for it.
Is it possible to utilize MAPP gas with a propane torch?
You must use a “Turbo-Torch” when working with MAPP gas; you cannot use a propane torch head. I use a Bernzomatic self-igniting burned head that came with MAPP bottles, and it has worked flawlessly with propane. Going in the opposite direction will not work. MAPP gas will not work with a propane-only torch head.
Is it possible to solder copper with propane?
A propane or MAPP gas torch can be used to solder copper (methylacetylene-propadiene propane). A yellow tank holds MAPP gas, while a blue tank has propane. MAPP gas is normally a little more expensive than propane, but it heats the pipe considerably faster. Propane works OK, but it takes longerwhich could be advantageous if you’re new to soldering copper and working with 3/4-inch or 1/2-inch piping. The torch you choose is entirely up to you.