Cleaning a ventless gas log set is a simple procedure that should be completed every year before lighting them. 1) The first item you’ll need is a vacuum cleaner with a hose and, ideally, a brush on the end of the hose. 2) Remove surface dust from the bottom of the fireplace around the gas log burner with the vacuum, then remove the log set from the burner and repeat the process. 3) Before you remove the logs from the burner, make sure you understand how to reinstall them correctly, as doing so incorrectly could cause the burner to emit soot. If you don’t have the owner’s handbook, take a picture to ensure proper placement.
4) To blow out the air mixing devices, you’ll need compressed air for the next step. You may do this with a basic can of air or a compressor. The pilot light assembly and the main burner orifice, where the gas is fed to the burner, are two crucial pieces that will need to be cleaned (s). 5) Locate the pilot light (the small flame that lights the main burners when you turn it on) and an oxygen depletion sensor (also known as an ODS) about 2 inches down from the tip of the pilot light. The ODS monitors the oxygen level in the room to ensure that it is at a safe level. It’s a very simple gadget with two small holes in it that continuously pull room air into them while the pilot light burns, as well as drawing in house hold dust in any house. 6) Once you’ve found the ODS, blow it out to clear the debris. The pilot light assembly is shown in the photos below. They don’t all look same, yet they’re all pretty similar.
7) Now you must clean the dust from the air intake to the primary burner(s) as indicated below (varies by model). Follow the gas tube supplying the burner up to where it enters the burner, and you’ll see an air gap between the orifice and the burner, which is the main burn intake that also draws oxygen from the room. If this portion becomes blocked, the gas will not be able to mix properly with the air as it flows into the gas log set, resulting in an incomplete combustion. 8) Once you’ve found the aperture, use compressed air to clean it out. Using compressed air, blow out all of the burner port holes, then reinstall the log set into the burner, making sure they are in the correct position.
Is it necessary to clean ventless gas fireplaces?
A minimum of once a year, your vent-free gas fireplace should be cleaned and serviced. If the appliance is heavily used or is located in an area with considerable traffic, dust, filth, or pet hair, it is advisable to clean it prior to the burning season and again in the middle of the season.
How do you clean the burner on a ventless gas fireplace?
Clean the inside of the firebox with a hose attached to the vaccum. Vacuum the outside as well, paying special attention to cobwebs and dust near vents. If necessary, use the scrub brush to dislodge debris or dust from crevices. Using the lint-free cloth, clean the gas valve. Vacuum the entire box one last time. Examine the inside of the firebox for any signs of damage.
If your fireplace has doors, clean them both inside and out with a non-ammonia cleanser.
Replace the logs, stones, and burner in the fireplace. It’s critical that they’re set exactly where they were before so that the logs don’t get too close to the flames.
Reconnect the electricity and gas, then relight the pilot light. Turn on the fireplace to ensure that everything is in working order.
Despite the fact that these logs are ventless, open one or two windows in your home to allow for adequate ventilation. The logs will burn cleaner as a result of this.
Turn off both the gas and the power to the fireplace. Before attempting to take anything from the fireplace, be sure the apparatus is cool.
Remove the logs, stones, and burner with care and set them on a piece of newspaper. Move everything outdoors and clean it up with the soft nylon bristle brush. Take special precautions with the logs, as they are quite delicate. Examine everything for any signs of wear or damage. You won’t need any cleaning supplies; all you’ll need is a cloth to finish the job.
What’s the best way to clean a ventless?
First and foremost, ensure that the heater’s power supply is turned off and that it has had time to cool down. To be safe, allow at least thirty to forty minutes.
Whether you haven’t used your heater in a while, check to see if all of the parts are rust-free and that insects haven’t taken up residence within.
Remove the cover from the top of the heater panel and inspect for any rusted or broken components.
If you discover that certain parts are severely damaged, contact a service professional for assistance in getting them replaced.
What is the best way to keep a ventless fireplace from smelling?
To keep odors from collecting near your fireplace, vacuum up pet hair and dust. A room air purifier will also aid in the purification of the air. Also, if you smoke, you should do so outside to avoid gathering residue around your fireplace. Deodorizers that plug into the wall and strong cleaning chemicals should be avoided.
Is it normal for a ventless gas fireplace to smell?
We get a lot of people who already have Ventless Gas Logs and are wondering why they smell, how to get rid of the smell, and other similar problems.
This article is intended to not only address that issue, but also to provide useful information to individuals considering acquiring a vent-free gas log now or in the future.
It’s important to note that this debate does not apply to vented gas logs.
Vented gas logs are burned with the damper fully open in wood-burning fireplaces, allowing the odor to rise up the flue. If you install vented gas logs, you will not have the odor problem outlined below unless your fireplace is improperly drafted.
For the purposes of this debate, I’ll use the term “natural gas.” Although the chemical makeup of Liquid Propane and the additives employed in its manufacturing differs from that of Natural Gas, the basic assumption below applies to both gases.
Ventless logs do emit a distinct odor, with some emitting more than others depending on the brand’s quality. There’s no way to avoid that; it’s just the nature of burning gas in your house without blowing the fumes up a chimney. Water vapor and carbon dioxide, neither of which have an odor, are the natural byproducts of burning “pure” natural gas in an ideal environment. However, because gas is never completely pure, we end up with various byproducts.
Methane gas (natural gas in its purest form) is made up of Carbon and Hydrogen molecules, as shown by the chemical formula that explains its combustion. When carbon is burned, it reacts with oxygen to form carbon dioxide, while hydrogen reacts with oxygen to make water vapor. Both of these gases are odorless and non-toxic. If the gas does not entirely burn, some carbon molecules remain as carbon (soot), while others mix with a single oxygen molecule to form carbon monoxide (which is still an odorless gas). Heat is produced as a final consequence of the process (-890 kJ/mol). The formula is as follows:
Note: If you notice soot forming on your logs, it’s likely that carbon monoxide is being created as well.
Unfortunately, we do not live in an ideal world, and the natural gas delivered to your home is no exception.
It contains trace levels of contaminants and additives, one of which is a rotten egg stench provided to help you detect a gas leak if one happens (again, natural gas in its raw state is odorless). Methyl Mercaptan is the most popular rotten-smelling ingredient. Sulfur Dioxide, a result of burning Mercaptan, smells like burnt matches combined with rotting eggs. When you add in other aromas caused by contaminants in the gas supply, you get the characteristic smell of ventless logs.
Furthermore, in higher concentrations, sulfur dioxide is an irritant to the eyes and respiratory tract.
Despite the fact that gas suppliers maintain that the amount of mercaptan added to natural gas is so small that it provides no health danger, many people report pain when burning ventless logs, particularly eye irritation and coughing episodes.
What can you do if you have ventless logs and can’t stand the stench?
- If you don’t want to burn your ventless gas logs,
- If your fireplace has a damper (and/or if you have a fireplace with a chimney…and/or if you have a fireplace with a chimney…and/or if you have a fireplace with
- Open some windows (to let fresh cold air in while attempting to warm your home)…and/or
- Change out your ventless log set for a vented one that may be burned with the damper fully open.
We sell R. H. Peterson Ventless Gas Logs, which are the oldest gas log manufacturer in the United States. Unlike less expensive brands found at home centers, we cannot guarantee that you will not encounter an odor with Peterson ventless logs. They are a premium brand that is designed to eliminate odor and maximize the realistic appearance. Many of our customers report no odor at all, however as previously noted, some scents are unavoidable due to contaminants in the gas supply.
Is it true that ventless fireplaces produce soot?
Ventless gas logs give more heat and don’t produce soot (when put properly), but they’re significantly less realistic. They also emit an odor that many people dislike or are unable to tolerate, therefore ventless gas logs should only be used if heat is the primary goal.
Is it necessary to clean a gas fireplace on a regular basis?
Gas fireplaces require a yearly inspection to stay in good working order. This is an extremely crucial practice that many people, including myself, ignore. Some people believe that because gas fireplaces burn clean and are simple to maintain, they don’t need to be cleaned. While it’s true that gas fireplaces are both efficient and low-maintenance, it’s also true that any device, if neglected, may become a nuisance. That is why you should inspect your gas fireplace once a year. You may set your mind at ease when you start your unit this season by cleaning your fireplace and chimney.
Each fireplace or insert should be cleaned at least once a year. This is due to the effort a fireplace expends each time it is used to heat your home. It’s recommended to have your fireplace checked every spring so you can enjoy a perfectly functioning fireplace all year, but whatever timetable works best for you will work for the fireplace as well.
Debris tends to congregate in the vents, the flue, and the interior of the chimney. This must be removed because it will obstruct ventilation and may stink. Debris from a gas fireplace includes:
1. Logs that are deteriorating
With use, ceramic or imitation log inserts can disintegrate, sticking to the insert’s sides and becoming trapped.
2. Scratched or dirty glass doors or frames
Over time, chipped or scratched glass might constitute a hazard. It has the potential to interfere with the heat output of your fireplace, which no one wants. You’ll need to have it cleaned or replaced if this is the case.
3. Remainder
Cleaning the inside and outside of a gas fireplace is necessary every now and then. After all, it’s bound to become a little grimy in there after all those beautiful fires. It’s critical to follow the manufacturer’s recommendations and only clean with approved products. Check with your technician or a local dealer to see whether cleaning services are available.
Remember to examine the logs every year if you have a masonry fireplace with a gas log set insert.
During an inspection, the technician will examine the outside first. This includes checking for chipped, fractured, or filthy glass, as well as ensuring that the structure is in good working order. The technician will inspect the interior gas ignition under the log structure for dents or debris as well as make sure it is lighting properly. They also check to see if your log collection is deteriorating in any manner. Often, the facade of the device will be removed so that the valves and connections beneath your fireplace or insert can be inspected. They’ll check to see whether your fireplace’s heat output is correct and clean off any residue that’s clogged any ports or vents. Following a routine inspection, your technician should ensure that you have working carbon monoxide detectors and that you are informed of any necessary repairs to your gas fireplace. Certified gas technicians are knowledgeable and will gladly answer any questions you may have about your fireplace or insert, so don’t be shy about asking.
When it comes to enjoying a blazing fire in your living room, safety always comes first. An annual inspection ensures that your lovely fireplace is operating at maximum efficiency for whenever you need that warm glow or extra warmth.
How can you fix a gas fireplace with a yellow flame?
You may allow proper ventilation by opening the fireplace damper. The color of the flame will be controlled by this. Reduce the air intake to give the flames an orange or yellow tip. This can be accomplished by adjusting the damper or closing the air shutter.
These adjustments are made with knobs hidden behind the beautiful front of the gas fireplace. If you need to remove these, ensure sure the fireplace is turned off and the front is cool before touching it. These settings may be on your gas fireplace’s remote if it came with one.
How do you clean the burner on a gas heater?
Remove the screws holding the heater’s cover panel in place, then remove the panel and clean the inside with warm water. Set aside the freshly washed area to dry.
Vacuum the parts within the propane heater gently, and brush out dust from around the oxygen sensor near the gas line tubing using the paintbrush.
Reinstall the panel cover and tighten the screws. As directed in the operating handbook, turn on the heater.
Check to see if the propane heater is switched off. Vacuum as much dust and dirt from the outside of the heater as you can, as well as inside the vent openings and grids.
Dust can be brushed away using a little paint brush in tight spaces. Gently brush the igniter and the flame locations on the heater with the brush.
Why isn’t my ventless propane heater working?
- When a propane heater won’t remain lit, it’s common for the gas heater to detect that the flame is malfunctioning in some way, triggering the propane heater’s safety mechanisms and shutting it down. It’s possible that the issue is a true flaw, or it could be a sensor issue.
- Check to see if the sensor device is 2/3 covered by the flame, or try wiping the gadget with sandpaper to see if that’s the case. This may help to solve the problem with your propane heater.
- The majority of propane heater issues may be traced back to a faulty pilot. You should be able to see the standing pilot of your gas heater through a small window or opening near the control knob if it has one. The pilot should be about an inch tall and primarily blue in color.
- The pilot tube should be cleaned if it is flickering, split, tiny, orange, or yellow in color. Turn off the gas first, then gently poke a needle into the top of the pilot tube to clean it out.
- If a draft is causing problems with the propane heater pilot, the best solution is to find and eliminate the source of the draft.
- The thermocouple could be the source of the problem as well. The thermocouple is a heat-sensitive safety device that prevents unburned gas from being released into the atmosphere. The thermocouple is heated by the pilot flame, signaling the valve to stay open and keep the pilot lit and the propane heater running.
- The pilot can go out and shut down the propane heater if the thermocouple is too far away from the flame; you can simply remedy this by repositioning the thermocouple closer to the flame.
- It’s also possible that the thermocouple has worn out and needs to be replaced. Remove the old one, unclip the bulb, unscrew the wire from the gas valve, and replace it in the same location. As a safety precaution, always turn off the gas.
- It’s possible that a problem with the electrical spark mechanism is to blame. When the blower is turned on, you should see a spark in the burner chamber. If you don’t have one, get an electrical diagram of the machine, which normally comes with the owner’s manual, and figure out what’s causing the problem.
- If your propane heater ignites but does not light, it is possible that the gas cylinder supplying it is empty or that the gas has been turned off. Check to make sure, and if the problem persists, use a needle to clean the gas valve.