1. Take the interior unit out of the casing.
2. Flip it over and lift the felt pad to reveal the fuel chamber packing material.
3.Apply lighter fluid slowly to the packaging material. When the fluid reaches the top of the packing or begins to change color, stop filling.
- Don’t overfill the container. The lighter will spill fuel if it is overfilled. Because the fluid is a skin irritant, avoid getting it on your skin. If skin contact occurs, wash the affected areas with gentle soap and water as soon as possible.
4. Replace the internal unit in the case, wiping away any residual liquid from the lighter and your hands before lighting it. If there is any fuel left on the lighter, wipe it off or wait for it to evaporate. Before lighting, make sure the gasoline can is closed and there is no spilt fuel nearby — this is a dangerous liquid.
- If you’re going to keep the lighter in your pocket, we recommend putting it in “bottom down.”
5. Make a spark by striking the flint wheel with your thumb in a downward motion. If no flame appears, try again.
6. When a flame appears and you’re done with it, close the lid to put it out. Because this lighter does not self-extinguish, the lid must be closed.
How long does it take to fill a butane torch?
Butane is not created equal. Stick to high-quality butane that has been triple-refined, if not four or five times. The majority of the low-cost generic brands found at convenience stores will not suffice. Why? Butane that hasn’t been refined, or that hasn’t been refined enough, has a greater amount of contaminants. Fuel impurities will block your lighter’s jets. Using the cleanest gasoline possible ensures that your lighter performs at its best and lasts a long time. High-quality, ultra-refined butane is produced by both Xikar and ST Dupont.
A crucial step is to bleed, or purge, your lighter. The fuel tank in your lighter fills with air when the butane in it is reduced by normal use. When you try to replenish an empty fuel tank, the air left at the end will prevent further fuel from entering the lighter. The air is released, totally emptying the tank and making place for a new, full injection of butane.
You’ll need a paper clip or a small, thin screwdriver to bleed your lighter. Press in on the fuel inlet valve at the bottom of your lighter using the straight end of the paperclip or the tip of your screwdriver. Keep the valve closed until all of the pressure has been released. It takes roughly 5 to 10 seconds on average. As the air and any remaining fuel are discharged from the tank, you will hear a hissing sound.
Turn the flame adjustment wheel to the lowest setting after all the air has been expelled. A (+) and a (-) indicate the flame adjustment setting (-). Turn the steering wheel all the way down to the bottom (-). This ensures a quick and effective filling while also preventing any trace quantities of surplus air from entering the tank.
Hold your lighter backwards. As you ready to refill the lighter, turn the butane can upside down. The reason for inverting the can is straightforward. There are two components in a can of butane: butane and propellant. Because propellant is lighter than butane, it is found near the top of the can, closer to the nozzle. As you prepare to insert the butane into the valve on your lighter, turn the can upside down to shift the butane closest to the fuel nozzle.
While the lighter fills, press the nozzle into the valve for about 5 or 10 seconds. As a result, the lighter will become chilly. You can visually monitor how much butane makes it into the tank if your lighter has a fuel window. Keep in mind that topping out a butane lighter is practically impossible. In the tank, there will always be a little pocket or bubble of air, which will show up in the fuel window.
- One method that always works for optimal speed and efficiency when refilling your lighter is to put it in the freezer for about 10 minutes after you bleed it and just before you refill it. The butane enters the tank as quickly and thoroughly as possible by cooling the lighter to a freezing temperature.
Wait 3 to 5 minutes after the tank is full before attempting to use the lighter. This allows any surplus butane (on the outside of your lighter) to evaporate, as well as giving the lighter time to cool down. With the (+) and (-) at the bottom, set the flame height to about the halfway. You don’t want to crank it all the way up to the (+) position right after a new refill because it can generate a massive explosion of flame. After you’ve lit the flame a few times, gradually raise it to the appropriate height. It’s now time to fire the next cigar!
Why does my torch lighter sputter?
The most common cause of a butane lighter sputtering or stopping to light is because it has run out of gas. It’s time to replenish the butane supply in the tank. We’ll go through some tips for doing a complete refill.
Another typical reason why a lighter won’t light is because the jets are clogged. This problem is more likely to occur with lighters that don’t have a cap to cover the top of the jets. Pocket lint and debris have the potential to clog the jets.
Using unrefined or low-quality butane might also cause the jets to clog. We’ve highlighted a few fast and easy solutions below to keep your cigar lighters running well.
How do you bleed a torch?
Hold the lighter in a vertical, upright posture to bleed. With a little screwdriver, depress the filler valve until all of the fuel is released and the hissing stops. Shake it lighter a second time to make sure it’s thoroughly bled.
Do you shake butane before filling?
Q. I recently purchased a new cigar lighter from my local cigar shop. I noticed that before inserting the needle into the lighter, the counter man shook the container. Is this really a good idea, given that the gas in the can is compressed?
We frequently shake a can or jar of liquid to see how much is left out of habit. While shaking a deodorant spray or an air freshener before refilling a butane lighter is acceptable, it is not acceptable to shake a can of butane before refilling a butane lighter!
The amount of propellant in the mixture that goes into the lighter tank is increased by shaking the can. Excess propellant, as well as anything else in the tank, will cause ignition problems.
Can a butane torch explode?
For a quick and easy high, some people have turned to inhaling butane from bottles or aerosols. Although breathing butane might cause euphoria, it can also cause a slew of medical issues, including blood pressure fluctuations, transient memory loss, frostbite, sleepiness, narcosis, hypoxia, cardiac arrhythmia, and, in the worst-case scenario, death. Butane is one of the most often mishandled chemicals, accounting for over half of all solvent-related deaths.
Butane, as a highly flammable and compressed gas, has the potential to explode if exposed to heat or utilized incorrectly. When used inappropriately, this volatile material has been known to hurt or even kill humans, as well as cause property damage and fires. Because butane gas is heavier than air, it can travel great distances before encountering a material that ignites it, then return to its source at breakneck speed.
Butane, in its purest form, is an odorless, colorless gas that is undetectable by humans until it causes health problems or an explosion. Fortunately, organic sulfur compounds are added to bottled butane to produce foul odors, allowing humans to identify a leak and flee before their safety is jeopardized.
Butane can induce frostbite or freeze burn if poured on exposed skin or eyes. Because of this, butane refills must be handled with caution. Adaptors for refilling various types of appliances will be included with butane bottles optimized for refilling.
How do you refill butane?
Shake your butane can and put the can’s stem against the refill valve (while in a straight up-and-down position). Hold for 5 seconds before releasing. Repeat as needed in shorter spurts until the tank is full.
How do you unclog a torch lighter?
Clean the lighter’s burner using compressed air. This is critical because compressed air should effectively remove the thick butane, smoke, and ash residue. The burner might become blocked and the lighter will stop working if it is not cleaned.